MVSP Series

stands for quality logo

ISO 9001:2015 Certified

Available With Trolley For Mobile Application

Keeping in view the fastest growing demand for transferring various types of solvents from the barrels to the overhead reaction vessel in pharmaceutical, bulk drugs and other process industries , all model is developed and is supplied with trolley for mobility .

UNIQUE PART OF PUMP

  • The initial prime is accomplished by partially filling pump priming chamber with liquid as in Sketch 'A'. This shows pump not in operation but the initial prime can just as readily be effected while pump is actually running.
  • The rotation of the impeller throws the liquid out between the blades towards the periphery by centrifugal force and at the same time imparts velocity to the liquid in the volute passage. The air being lighter remains in the center of the cage. The volute has its maximum cross-sectional area between points at the bottom section of the impeller cage and decrease in area in either direction from this point.
  • As a pair of blades approach the discharge, the liquid is forced (by centripetal action) between them, down towards the center due to the decrease cross-sectional area of the volute. This, in effect, provides a positive liquid piston action, pushing the air at the center out through the discharge port and into the discharge pipe. The space between blades as they pass the extreme end of the discharge port, is now completely filled with liquid which is retained therein until the bridge or sealing surface between the discharge and suction ports has been crossed.
  • Once past the bridge, however, the liquid between the impeller blades is thrown out into the volute passage which increase in cross-sectional area.
  • This again provides the positive liquid piston action away from the center of the pump, reducing the pressure over the suction port and air in the suction pipe is forced up into the pump as a result. This action, continues until all air has been evacuated from the suction line. Sketch 1B' shows the air pumping stage and illustrates the eccentric liquid ring effect formed within the casing. This actually amounts to definite suction and discharge strokes of liquid piston within the pump and is the reason for its positive timing action.
  • After all the air has been evacuated from the suction line, the pump commences and will continue to pump liquid on exactly the same basis, this being illustrated in Sketch 'C'. If the pump breaks suction, it will pump air until suction line is again submerged and then pick up the liquid again. No foot or check valves are needed. Sketch 'C' shows bubbles of air in the liquid flowing through the pump. It has great air handling ability. Minor leaks in the suction line, therefore, do not effect operation neither will a loop in the suction line.
  • When the pump is stopped the liquid is retained in the pump casing and the pump is ready without any further priming to start pumping.
  • Mechanically the pump is similar to a conventional centrifugal design only two operating parts, impeller and shaft with the same running fit. Therefore, its service life will be the same as that of a centrifugal pump under same working conditions.
Capacity upto 21 M3/Hr
Head upto 35 Mts
Power upto 5.5 Kw
  • Low NPSH required
  • Life lubricating bearings, covered from both the ends so minor leakage from pump side does not affect bearings
  • Being a low speed (1450 RPM) pump, Less Maintenance is needed
  • Installation is easier since motor required is vertical flange type and is directly coupled to the pump, coupling alignment is simpler
  • Low overhang shaft arrangement giving minimum deflection at the seal faces
  • Floating type impeller reduces noise and vibration
  • Available only with mechanical seal (internal mounted), rotary faces of Carbon and High alumina Ceramic (Al203)
  • Seal cooled and flushed by process fluid itself
  • Minor leakage at suction side does not affect pump performance
  • Biggest advantage from installation point of view is that since it is an "in line" type pump, it can be fitted as a valve and hence it will not require any suction or delivery piping efforts
  • High head low capacity pump
  • Available in SS-316 INVESTMENT CASTING and as per requirement
  • Excellent for handling solvents from barrels and from tank farms to the charging vessels
  • Seal leakage can easily be detected from window in priming chamber
  • Pump can take negative lift from 3 to 5 meters Maintenance is easier, Drain arrangement is standard Compact design - requires less space, No grouting required

Note : Since the pump is having close tolerance and always fitted with mechanical seal it is advisable to have a suitable strainer before pump inlet.

Copyright © 2020 Mackwell Pumps & Controls.All Rights Reserved.